Top 10 Bipolar Stepper Motor – Telescope Motor Drives

As an Amazon Associate I earn from qualifying purchases.

1. STEPPERONLINE

#ad

STEPPERONLINE Short Body Nema 17 Bipolar Stepper Motor 1A 22.6oz.in/16Ncm DIY CNC Extruder

#ad
STEPPERONLINE #ad - Rated current 1. 0a & resistance 3. 5ohms. Nema 17 bipolar 1. 65"x1. 65"x079" 4-wire. Step angle200 steps/rev. 1. 8 deg. 16ncm22. 6oz. In holding torque. Short height, Small Size.
BrandSTEPPERONLINE #ad
ManufacturerOSM Technology Co.,Ltd. #ad
Height0.79 Inches
Length1.65 Inches
Weight0.31 Pounds
Width1.65 Inches
Part Number17HS08-1004S
Model17HS08-1004S

2. RATTMMOTOR

#ad

5Pcs Nema 17 Stepper Motor 40mm 64oz-in 45Ncm 1.7A 1.8 degree 2 phase with 1M 4-pin Cable & Connector Bipolar 42 stepping motor for 3D Printer Hobby CNC Router Machine 17HS4401J

#ad
RATTMMOTOR #ad - It with 1. 8°± 5%step angle 200 steps/revolution Phase:2. Motor type: bipolar Stepper;Motor with 1M 4-pin Cable. 42 * 42 * 40mm. Step angle:1. 8deg;rated Current:1. 7a. Holding torque: 045nm64 oz. In;product Dimensions: 1. 6 x 1. 5 x 1. 6 inches. Nema17 stepper motor 40mm;size l * w * H: ca.
BrandRATTMMOTOR #ad
ManufacturerChangzhou Rattm Motor Co.,Ltd #ad
Part NumberS17
Model3216594568

3. OSM Technology Co.,Ltd.

#ad

STEPPERONLINE Micro Stepper Motor Nema 11 Bipolar Stepping 0.67A 17oz.in/12Ncm 1.8deg 4 Leads

#ad
OSM Technology Co.,Ltd. #ad - Rated current 067a, step Angle 1. 8°, resistance 9. 2ohms. Frame size 28 x 28mm, Body Length 51mm. 4-wires black, Blue, Green, Red. Shaft diameter Φ5mm, Shaft Length 20mm. Nema 11 hybrid bipolar stepper motor, 12Ncm17oz-in holding torque.
BrandOSM Technology Co.,Ltd. #ad
ManufacturerSTEPPERONLINE #ad
Height2 Inches
Length1.1 Inches
Width1.1 Inches
Part Number11HS20-0674S
Model11HS20-0674S

4. SMAKN

#ad

SMAKN CNC Micro-Stepping Stepper Motor Driver M542/DM542 Bi-Polar 2phase 4.5A Switch

#ad
SMAKN #ad - H-bridge bipolar constant phase flow driver. The maximum output current is 4. 5a eight optional. Up to 32 segments of six kinds of sub-modes available. The input signal high-speed photoelectric isolatio. 24v-50v dc power supply.
BrandSMAKN #ad
ManufacturerSMAKN #ad

5. Longruner

#ad

Longruner 5X Geared Stepper Motor 28byj 48 Uln2003 5v Stepper Motor Uln2003 Driver Board with ArduinoIDE no Wire

#ad
Longruner #ad - 5pcs stepper motor and driver board compatible with 2560 1280 DSP ARM PIC AVR STM32 Raspberry Pi. Stepper motor with a standard interface. Good after-sales service. A, c, b, d four-phase led indicates the status of the stepper motor work. Motor diameter: 1. 1 inches. Wire length:9. 05 inchs. Cable length: about 20cm /8-inch. Great packing in a box : 5 set Uln2003 Stepper Motor + Driver Board. Stepping angle: 5. 625 x 1/64. Reduction ratio: 1/6. Drive module Board Size:1. 26 inchsX1. 38inchs.
BrandLongruner #ad
ManufacturerLongruner #ad
Part NumberLK67
ModelLK67
Warranty1 year warranty

6. RuiLing

#ad

RuiLing 4PCS 1.5M 59 Inch Stepper Motor Cables Lead Wire HX2.54 4 Pin to 6 Pin

#ad
RuiLing #ad - Equipped with two connectors. Size: about 150 * 05 * 02cm/59 * 02 * 009inchl*W*H;. Made of high quality material, it is durable and long lasting use. It is compatible with many stepper models. 4 pin dupont connector of the driver side, compatible with RAMPS board and other.
BrandRuiLing #ad
ManufacturerRuiLing #ad
Part NumberSMCABLE-1.5M-4

7. Adafruit

#ad

NEMA-17 Size, 200 Steps/rev, 12V 350mA, Adafruit PID 324 Stepper Motor

#ad
Adafruit #ad - Bipolar stepper, requires 2 full h-bridges! 12v rated voltage you can drive it at a lower voltage, but the torque will drop at 350mA max current. 4-wire, 8 inch leads. 200 steps per revolution, 1. 8 degrees. Coil #1: red & yellow wire pair. 42mm/1. 65" square body 31mm/1. 22" square mounting holes, 24mm long, 3mm metric screws M3 5mm diameter drive shaft, with a machined flat. Coil #2 green & Brown/Gray wire pair.
BrandAdafruit #ad
ManufacturerAdafruit #ad
Height1 Inches
Length3 Inches
Weight0.19 Pounds
Width2 Inches

8. Adafruit

#ad

Adafruit DC & Stepper Motor HAT for Raspberry Pi, Mini Kit

#ad
Adafruit #ad - Requires soldering of header pins. Works best with raspberry Pi model A+, B+, or Pi 2. Up to 4 bi-directional dc motors with individual 8-bit speed selection so, about 05% resolution. Up to 2 stepper motors unipolar or bipolar with single coil, double coil, interleaved or micro-stepping. Can run motors on 4. 5vdc to 13. 5vdc. 4 h-bridges: tb6612 chipset provides 1. 2a per bridge 3a peak with thermal shutdown protection, internal kickback protection diodes.
BrandAdafruit #ad
ManufacturerAdafruit Industries #ad
Height1 Inches
Length3 Inches
Weight0 Pounds
Width2 Inches
Part Number2348
Model2348

9. Geekworm

#ad

3B+/3B/2B/B+ Stepper/Motor/Servo/IR Remote, Geekworm Raspberry Pi 4B/3B+/3B Full Function Motor HAT, Robot Expansion Board Support Raspberry Pi 4 Molde B

#ad
Geekworm #ad - One infrared receivergpio26 with big terminal block connectors to easily hook up wires 18-26AWG and power, Polarity protected 2-pin terminal block and jumper to connect external 5-12VDC power.

Can run motors on 5VDC to 12VDC. Up to 4 bi-directional dc motors with individual 8-bit speed selection; Up to 2 stepper motors unipolar or bipolar with single coil, double coil, interleaved or micro-stepping; Up to 4 Channel 12-bit PWM/Servo5V. Diy product, do not provide sample code. 4 h-bridges: tb6612 chipset provides 1. 2a per bridge 3a peak with thermal shutdown protection, internal kickback protection diodes.

Diy your robot! stepper motor/servo/motor/sensors/ir romote full function motor hat Robot Expansion Board for Raspberry Pi 4 / 3B / 3 B+ / 2B / B+ / Zero. Video&document refer to geekworm wiki search robot_Expansion_Board, all the information are on the WIKI page, this is a DIY product, pls read the information carefully.
BrandGeekworm #ad
ManufacturerGeekworm #ad
Height2.2 Inches
Length2.56 Inches
Width0.79 Inches
Part NumberTB-2017-15
ModelTB-418460

10. TIMESETL

#ad

TIMESETL 5Pack L298N Stepper Motor Driver Controller Board Dual H Bridge Module for Arduino Electric Projects

#ad
TIMESETL #ad - This l298n board comes ready to go. Wide usage great for for arduino diy smart car robot power uno mega r3 Mega2560 Duemilanove, if driving voltage is more than 12V, use external standard 5volt TTL outputs to switch the H-bridge circuits.

Just wire up motors and power, easy to use. High quality main driver chip l298n, strong driving ability, strong anti-interference, low calorific value, afterflow diode protection, more stable and reliable for Arduino projects. Parameter external size 43*43*27mm / 1. 69*1. 69*1. 06 inch, voltage 5v-35V, drive current 2A Max single bridge. Easy to use no assembly required. High efficient double h bridge design, can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors, high efficient.
BrandTIMESETL #ad
ManufacturerTIMESETL #ad
Height1.18 Inches
Length5.91 Inches
Width3.15 Inches
Part NumberTXJ-061-EU
ModelL298N motor controller