Top 9 Load Cell Amplifier – Power Converters

As an Amazon Associate I earn from qualifying purchases.

1. Calt

#ad

Weighing Scale Load Cell Amplifier JY-S60 24Vdc Supply Voltage Current Converter Weight Transmitter 0-5V 0-10V 4-20mA E10v-2.0mv/v

#ad
Calt #ad - Accuracy: better than 02% f. S. Output excitation: output Excitation Voltage: 5V~15VE+ are ok. Output signal: 0-5v, 0-10V, 4-20MA. Operating voltage: 24VDC. Input signal: sensor.
BrandCalt #ad
ManufacturerCALT #ad
Height3.54 Inches
Length5.91 Inches
Width7.87 Inches
Part NumberJY-S60

2. KOOKYE

#ad

KOOKYE 5kg Load Cell and HX711 Combo Pack Kit, Load Cell Amplifier ADC Weight Sensor for Arduino Scale

#ad
KOOKYE #ad - Hx711 - this top of the line load cell amplifier mounted on a breakout board pairs perfectly with the load cell to provide fast, accurate force measurements.

4 mounting holes, 12. 7 mm wide, the other side both holes tapped M5 thread. Accurately measures forces from 0-5kg 0-11 lb. Load cell - sturdy aluminum alloy construction with strain gauges pre-attached with strain relieved wires. Dimensions 12. 7 mm high, 15 mm spacing on each side. Load cell specs - 22 cm 8. 5 in wire leads pre-attached. It measures small changes in the resistance of the strain gauges mounted to the load cell and passes these values directly to any micro controller like an Arduino or Raspberry Pi. One both holes tapped M4 thread, 80 mm long 05 in x 05 in x 3. 15 in.
BrandKOOKYE #ad
ManufacturerKOOKYE #ad
Part Number2020001500
Model2020001200

3. CHENBO

#ad

CHENBO Load Cell Weight Sensor 1kg + HX711 Weight Weighing A/d Module Pressure Sensor

#ad
CHENBO #ad - Accurate measures forces from 0-5kg 0-11 lb. Selectable 10sps or 80SPS output data rate. Input end: red+, black-; output end: green+, White-; Excitation Voltage: 5-10V DC. On-chip active low noise pGA with selectable gain of 32, 64 and 128. Simple digital control and serial interface: pin-driven controls, no programming needed. Sturdy aluminum alloy construction with strain gauges pre-attached with strain relieved wires.
BrandCHENBO #ad
ManufacturerCHENBO #ad
Part NumberNCOREDSHJKJKF7938
ModelNCOREDSHKF7938

4. NOYITO

#ad

Load Cell Amplifier ADC Weight Sensor 1kg+HX711, NOYITO 1kg 5kg 10kg 20kg Load Cell and HX711 Combo Pack Kit

#ad
NOYITO #ad - Accurate measures forces from 0-5kg/ 5kg /10kg /20kg. Br>. Dimensions 12. 7 mm high, 15 mm spacing on each side. 4 mounting holes, the other side both holes tapped M5 thread. Br>. Hx711 specs: operation voltage: 2.

7v-5v ; operation current: < 1. 5ma ; selectable 10sps or 80sps output data rate ; Includes breakaway headers for connection, soldering required. Br>. It measures small changes in the resistance of the strain gauges mounted to the load cell and passes these values directly to any micro controller like an Arduino or Raspberry Pi. Br>. One both holes tapped M4 thread, 12.

7 mm wide, 80 mm long 05 in x 05 in x 3. 15 in. Please choose the correct specification before buying. Hx711 :this top of the line load cell amplifier mounted on a breakout board pairs perfectly with the load cell to provide fast, accurate force measurements. Load cell:sturdy aluminum alloy construction with strain gauges pre-attached with strain relieved wires. Load cell specs: 22 cm 8.
BrandNOYITO #ad
ManufacturerNOYITO #ad
Weight0.02 Pounds
Part Number43237-2

5. DWZ

#ad

LIVISN 20kg Load Cell and HX711 Combo Pack Kit, Everything Needed for Accurate Force Measurement, Load Cell Amplifier ADC Weight Sensor for Arduino Scale

#ad
DWZ #ad - Accurately measures forces from 0-5kg 0-11 lb. Hx711 - this top of the line load cell amplifier mounted on a breakout board pairs perfectly with the load cell to provide fast, accurate force measurements.

Hx711 specs - operation voltage: 2. 7v-5v | operation Current: < 1. 5ma | includes breakaway headers for connection, soldering required. It measures small changes in the resistance of the strain gauges mounted to the load cell and passes these values directly to any micro controller like an Arduino or Raspberry Pi. Dimensions 12. 7 mm high, 12. 7 mm wide, 80 mm long 05 in x 05 in x 3. 15 in. Load cell - sturdy aluminum alloy construction with strain gauges pre-attached with strain relieved wires. Load cell specs - 22 cm 8. 5 in wire leads pre-attached. One both holes tapped M4 thread, the other side both holes tapped M5 thread. 4 mounting holes, 15 mm spacing on each side.
BrandDWZ #ad
ManufacturerLIVISN #ad
Part NumberHX711 20KG

6. SparkFun

#ad

SparkFun OpenScale Simple-to-use Open source solution for measuring weight and temperature Includes HX711 24-bit ADC for weigh scales TMP102 FT231 with mini USB, for USB to serial connection

#ad
SparkFun #ad - Atmega328p microcontroller. Power cycling above 500ms. Selectable 10sps or 80sps output Data Rate. Local & external temperature Sensors. Turn a load cell or four load sensors, in a Wheatstone bridge configuration, into the DIY weigh scale. Fixed & Adjustable Gain. Operating voltage: 5v. A precision digital temperature sensor to report the local temp. Add a four or five wire load cell of any capacity. Operating amperage: 80-100mA.
BrandSparkFun #ad
ManufacturerSparkFun Electronics #ad
Height2.95 Inches
Length3.94 Inches
Weight0.03 Pounds
Width0.59 Inches
Part NumberSEN-13261
ModelSEN-13261

7. APC

#ad

APC UPS, Back-UPS Series Uninterruptible Power Supply, USB Charger, 600VA UPS Battery Backup & Surge Protector, BE600M1 Backup Battery Power Supply

#ad
APC #ad - One usb charger port 1. 5a for cell phones and other portable electronics. Replaceable battery: the battery can be replaced when needed with RBC model APCRBC154 sold separately. 600va / 330w backup Battery power supply. 7 outlets nema 5-15r: 5 ups battery backup with Surge Protection Outlets, and 2 Surge Protector Only Outlets. Backed by apc's 3-year warranty, plus a $75, 000 connected-equipment policy. 5' power cord, right-angle 3-prong wall plug nema 5-15p, wall-mountable, plus FREE Windows PC power-management software Mac OS uses native "Energy Saver" Settings.
BrandAPC #ad
ManufacturerAPC #ad
Height5.47 Inches
Length10.79 Inches
Weight7.5 Pounds
Width4.13 Inches
Part NumberBE600M1
ModelBE600M1
Warranty3 years repair or replace

8. subroad

#ad

Office Signal Extend Coverage Up to 5,000 Sq Ft, Verizon Signal Booster 4G LTE Cell Phone Signal Booster Subroad 700Mhz Band 13 Mobile Cellular Repeater Amplifier Kit for Home

#ad
subroad #ad - We have professional technical team support, if you have any questions, please contact us. Supports multiple devices simultaneously in-home or office, Tablets, Windows Phone system, Modems, Wi-Fi Hotspots can all directly connect at the same time. The booster simply amplifies your existing signal to give you more bars and maintain fast data speeds while you browse the internet or talk on the phone.

Also suitable for all systems including IOS, Android, Smart Phones, etc. You and your family will get more clear voice while making phone calls and enjoy faster Data when streaming videos. Boost 4g lte data signal-this cell phone booster boosts enhance your cell phone signal, faster high-speed 4G LTE internet, fast your data uploads & downloads, reduce dropped calls in-home or office,higher audio quality. Quality service- once the subroad home 4g booster is installed, the device will improve indoor mobile signals, making voice calls more reliable in terms of connectivity and meaning that call loss rates will be greatly reduced.

Enhanced range-signal-boosting the range of up to 5, 000 sq ft. Compatibility-this cell phone booster boosts 4g lte data signal for multiple cellular devices simultaneously. Applicable operator-this signal booster is suitable for Verizon band 13 700MHz 4G LTE. So all your family or friends can share one booster for more fun.
Brandsubroad #ad
ManufacturerSubroad #ad

9. DWZ

#ad

Everything Needed for Accurate Force Measurement, LIVISN 1kg Load Cell and HX711 Combo Pack Kit, Load Cell Amplifier ADC Weight Sensor for Arduino Scale

#ad
DWZ #ad - Dimensions 12. 7 mm high, 80 mm long 05 in x 05 in x 3. 15 in. It measures small changes in the resistance of the strain gauges mounted to the load cell and passes these values directly to any micro controller like an Arduino or Raspberry Pi.

Accurately measures forces from 0-5kg 0-11 lb. Load cell specs - 22 cm 8. 5 in wire leads pre-attached. One both holes tapped M4 thread, the other side both holes tapped M5 thread. Load cell - sturdy aluminum alloy construction with strain gauges pre-attached with strain relieved wires. Hx711 specs - operation voltage: 2. 7v-5v | operation Current: < 1. 5ma | includes breakaway headers for connection, soldering required. Hx711 - this top of the line load cell amplifier mounted on a breakout board pairs perfectly with the load cell to provide fast, accurate force measurements. 4 mounting holes, 12. 7 mm wide, 15 mm spacing on each side.
BrandDWZ #ad
ManufacturerLIVISN #ad
Part NumberHX711 1KG