WHDTS D1 Mini NodeMcu 4M Bytes Lua WiFi Development Board Base on ESP8266 ESP-12F Compatible Arduino

WHDTS - The firmware is based on the Espressif NON-OS SDK and uses a file system based on spiffs. The code repository consists of 98. 1% c-code that glues the thin Lua veneer to the SDK. An open-source firmware and development kit that helps you to prototype your IOT product within a few Lua script lines. The nodemcu firmware is a companion project to the popular NodeMCU dev kits, ready-made open source development boards with ESP8266 chips Features: 1>.

Open-source 2>. Interactive 3>. Programmable 4>. Low cost 5>. Simple 6>. Smart 7>. Wi-fi enabled 8>. Usb-ttl included 9>. 11 digital input/output pins, all pins have interrupt/pwm/I2C/one-wire supportedexcept D0 10>. 1 analog input3. 2v max input 11>. A micro usb connection 12>. Compatible with Arduino 13>. Compatible with nodemcu 14>.

WHDTS D1 Mini NodeMcu 4M Bytes Lua WiFi Development Board Base on ESP8266 ESP-12F Compatible Arduino - Compatible with MicroPython Parameters : 1>.

More information about WHDTS

HiLetgo 2pcs Wemos D1 Mini Development Board ESP8285 V1.0.0 1MB Flash Lite Wireless WiFi Internet Development Board Wemos D1 Mini ESP8285

HiLetgo® - For example d5 is equivalent to GPIO 14. Use a led to test if it will lit. Package including: 2* d1 mini development Board This is a powerful internet of things development board; standalone board mount, stackable on top, or stackable top and bottom. Although these d1 minis have only 16 pins, a reset pin, plus the ground and one 3 volt and one 5 volt pin.

. If you installed an earlier version of the driver the one I had had no version number in the file name search for instructions to remove it. Set the "reset Method" to: nodemcu. Go into the preferences and add the url as stated in the product description above sorry can't post the url here. Solder properly. You will want the files under the ch340g-ch34g-ch34x-mac-os-x-driver repository.

HiLetgo 2pcs Wemos D1 Mini Development Board ESP8285 V1.0.0 1MB Flash Lite Wireless WiFi Internet Development Board Wemos D1 Mini ESP8285 - This is enough for most projects. Pros: * smaller form than the standard nodemcu * 4mb flash memory * solid build * Usb power works * Works well with Micropython firmware * The Nodemcu/Lua firmware also works fine Steps for usage: * Download the Arduino IDE from the arduino. Cc site at en/Main/Software. I found an osX driver for the board at github.

Com on "adrianmihalko" 's page. Select the new "port" added by the driver: mine was "/dev/cu.

More information about HiLetgo®


Similar products



Gowoops 2 PCS DHT22 Temperature Humidity Sensor Module Digital Measurement for Arduino Raspberry Pi 2 3

Gowoops - User manual: http://osoyoo. Com/?p=15718http://osoyoo. Com/?p=21402specification:type: dhT22 temperature and humidity sensorOperate Voltage: DC 3~5. 5vsignal output type: digitaltemperature range: -40 ℃ ~ 80 ℃Temperature Measurement Accuracy: ± 05 ℃humidity range: 0~100%rhhumidity measurement accuracy: ± 2%RH Dimensions:Size: 40 x 15 x 9 mm L / W / HScrew hole diameter: 2.

6mmweight: 6gpackage included:2 x dht22 sensor module2 x Cable This is a powerful internet of things development board; standalone board mount, stackable on top, or stackable top and bottom. Although these d1 minis have only 16 pins, a reset pin, plus the ground and one 3 volt and one 5 volt pin. This is enough for most projects.

Gowoops 2 PCS DHT22 Temperature Humidity Sensor Module Digital Measurement for Arduino Raspberry Pi 2 3 - P>please choose the original seller: Gowoops, we don't guarantee the quality of the products bought from other seller. P>temperature range: -40 ℃ ~ 80 ℃, humidity Range: 0~100%RH. After all, you're still getting 10 digital i/o and the one A0 analog pin, you do get the hardware I2C and SPI pins on D5 through D8.

This d1 definitely fits on a standard breadboard leaving one open hole available for each pin on both sides but being shorter than the 30 pin boards you will have about 6 more rows available for prototyping, especially nice when using the short 460 tie point breadboards. 11 digital input / pwm / i2c / output pins, all pins with interrupt / support 1 line except D0; 1 analog input3.

2v max input.

More information about Gowoops


Similar products



HiLetgo 2pcs ESP8266 NodeMCU LUA CP2102 ESP-12E Internet WiFi Development Board Open Source Serial Wireless Module Works Great with Arduino IDE/Micropython Pack of 2PCS

HiLetgo 3-01-0268 - Built-in micro-usb, with flash and reset switches, easy to program. Download and run the 32 bit flasher exe at GithubSearch for nodemcu/nodemcu-flasher/tree/master/ at Github github. Com/nodemcu/nodemcu-flasher/tree/master/Win32/Release Or download and run the 64 bit flasher exe at: github. Com/nodemcu/nodemcu-flasher/tree/master/Win64/Release 7.

Data download access to the website: http://www. Nodemcu. Com. 8. Micro usb connection; compatible with Arduino; 1MB Flash; 500mA resettable fuse. Be aware that the old driver can cause your machine to lock up. In arduino ide, look for the old fashioned Blink program. Install the IDE 3. Set up your chip as: tools -> Board -> NodeMCU 1.

HiLetgo 2pcs ESP8266 NodeMCU LUA CP2102 ESP-12E Internet WiFi Development Board Open Source Serial Wireless Module Works Great with Arduino IDE/Micropython Pack of 2PCS - 0 esp-12e module tools -> flash size -> 4m 3m spiffs tools -> cpu frequency -> 80 mhz tools -> Upload Speed -> 921600 Tools-->Port--> whatever it is 6. Go to tools > board > board manager> Type "esp8266" and download the Community esp8266 and install. Note: please contact us if you need the driver or meet any issue when using.

Download the Arduino IDE, the latest version.

More information about HiLetgo 3-01-0268


Similar products



IZOKEE D1 Mini NodeMcu Lua 4M Bytes WLAN WIFI Internet Development Board Base on ESP8266 ESP-12F for Arduino, 100% Compatible with WeMos D1 Mini Pack of 5 …

IZOKEE IZKE29-5 - This is enough for most projects. 11 digital input/output pins, all pins have interrupt/pwm/I2C/one-wire and a micro-USB connection. P>temperature range: -40 ℃ ~ 80 ℃, humidity Range: 0~100%RH. Package includes: 5 x d1 mini nodemcu lua wlan wifi internet Development Board This is a powerful internet of things development board; standalone board mount, stackable on top, or stackable top and bottom.

Although these d1 minis have only 16 pins, a reset pin, plus the ground and one 3 volt and one 5 volt pin. After all, you're still getting 10 digital i/o and the one A0 analog pin, you do get the hardware I2C and SPI pins on D5 through D8. This d1 definitely fits on a standard breadboard leaving one open hole available for each pin on both sides but being shorter than the 30 pin boards you will have about 6 more rows available for prototyping, especially nice when using the short 460 tie point breadboards.

IZOKEE D1 Mini NodeMcu Lua 4M Bytes WLAN WIFI Internet Development Board Base on ESP8266 ESP-12F for Arduino, 100% Compatible with WeMos D1 Mini Pack of 5 … - 11 digital input / i2c / output pins, all pins with interrupt / pwm / support 1 line except D0; 1 analog input3.2v max input. 1 micro USB connection. How to get it started in arduino: - Setup driver Before you use mini D1 boards, you need set up CH340g driver. Arduino compatible, works great with the latest Arduino IDE/Mongoose IoT/Micropython.

Data download access to the website: http://www.

More information about IZOKEE IZKE29-5


Similar products



HiLetgo FT232RL FTDI Mini USB to TTL Serial Converter Adapter Module 3.3V 5.5V FT232R Breakout FT232RL USB to Serial Mini USB to TTL Adapter Board for Arduino

HiLetgo® 3-01-0661-1 - Pitch:2. 54mm. P>single-bus digital signal output, bidirectional serial data. Micro usb connection; compatible with Arduino; 1MB Flash; 500mA resettable fuse. Be aware that the old driver can cause your machine to lock up. This d1 mini module is a mini WIFI board based on ESP-8266EX. This wlan board contains 11 digital input / I2C / output pins, all pins have interrupt / pwm / 1-wire and a micro-USB connection.

Our d1 mini development board is 100% compatible with Arduino WeMos and can be programmed in the Arduino IDE. Chipset: ft232rl, not genuine ftdi chip, Working Voltage: 3. 3v/5. 5v. Firmware link: https://github. Com/nodemcu/nodemcu-firmware. After all, you're still getting 10 digital i/o and the one A0 analog pin, you do get the hardware I2C and SPI pins on D5 through D8.

HiLetgo FT232RL FTDI Mini USB to TTL Serial Converter Adapter Module 3.3V 5.5V FT232R Breakout FT232RL USB to Serial Mini USB to TTL Adapter Board for Arduino - This d1 definitely fits on a standard breadboard leaving one open hole available for each pin on both sides but being shorter than the 30 pin boards you will have about 6 more rows available for prototyping, especially nice when using the short 460 tie point breadboards. 11 digital input / pwm / output pins, all pins with interrupt / i2c / support 1 line except D0; 1 analog input3.

2v max input. If you installed an earlier version of the driver the one I had had no version number in the file name search for instructions to remove it.

More information about HiLetgo® 3-01-0661-1


Similar products



HiLetgo 5pcs DHT11 Temperature and Humidity Sensor Module for Arduino Raspberry Pi 2 3

HiLetgo 3-01-0039-1 - The simple communication protocol greatly reduces the programming effort required. Rxd/txd transceiver communication indicator, with 500MA self-restore Fuse. Specification: Power supply voltage: 3. 3~5. 5v dc output: the single bus digital signal measuring range: 20-90%rh humidity, temperature +-2 ° resolution: 1%RH humidity, temperature 0~50° The measurement accuracy of +-5%RH: humidity, temperature 1 ° Exchangeability: fully interchangeable Long term stability: < ± 1%RH Size: 28 * 12 * 7.

2mm interface Description: 1. Vcc:external 3. 3 v-5 v 2. Gnd:external Gnd 3. Do:small board switch digital output interface, connect the microcontroller IO port Package Included: 5* DHT11 Module 5* Dupont Cable This is a powerful internet of things development board; standalone board mount, stackable on top, or stackable top and bottom.

HiLetgo 5pcs DHT11 Temperature and Humidity Sensor Module for Arduino Raspberry Pi 2 3 - Although these d1 minis have only 16 pins, a reset pin, plus the ground and one 3 volt and one 5 volt pin. After all, you're still getting 10 digital i/o and the one A0 analog pin, you do get the hardware I2C and SPI pins on D5 through D8. This d1 definitely fits on a standard breadboard leaving one open hole available for each pin on both sides but being shorter than the 30 pin boards you will have about 6 more rows available for prototyping, especially nice when using the short 460 tie point breadboards.

11 digital input / output pins, all pins with interrupt / i2c / pwm / support 1 line except D0; 1 analog input3.2v max input.

More information about HiLetgo 3-01-0039-1


Similar products



MakerFocus 2pcs I2C OLED Display Module 0.91 Inch I2C SSD1306 OLED Display Module Blue I2C OLED Screen Driver DC 3.3V~5V for Arduino

MakerFocus - Firmware link: https://github. Com/nodemcu/nodemcu-firmware. After all, you're still getting 10 digital i/o and the one A0 analog pin, you do get the hardware I2C and SPI pins on D5 through D8. This d1 definitely fits on a standard breadboard leaving one open hole available for each pin on both sides but being shorter than the 30 pin boards you will have about 6 more rows available for prototyping, especially nice when using the short 460 tie point breadboards.

11 digital input / pwm / i2c / output pins, all pins with interrupt / support 1 line except D0; 1 analog input3.2v max input. Rxd/txd transceiver communication indicator, with 500MA self-restore Fuse. P>single-bus digital signal output, bidirectional serial data. Micro usb connection; compatible with Arduino; 1MB Flash; 500mA resettable fuse.

MakerFocus 2pcs I2C OLED Display Module 0.91 Inch I2C SSD1306 OLED Display Module Blue I2C OLED Screen Driver DC 3.3V~5V for Arduino - Be aware that the old driver can cause your machine to lock up. P>please choose the original seller: Gowoops, we don't guarantee the quality of the products bought from other seller. P>temperature range: -40 ℃ ~ 80 ℃, humidity Range: 0~100%RH. 2pcs i2c oled display Module 091 inch i2c ssd1306 oled display module blue I2C OLED Screen Driver DC 3.

More information about MakerFocus


Similar products



SHELLY 1 One Smart Relay Switch Wireless WiFi Home Automation iOS Android Application 2 Pack

Allterco Robotics EOOD NA - Micro usb connection; compatible with Arduino; 1MB Flash; 500mA resettable fuse. Be aware that the old driver can cause your machine to lock up. The shelly 1 os are Google home and Amazon Echo Compatible. Shelly 1 is extremely compact and can fit in variety of electrical consoles. P>operate voltage: dc 3~5. 5v.

This is enough for most projects. Open source - use the power of mongoose os to make your own application. P>temperature range: -40 ℃ ~ 80 ℃, humidity Range: 0~100%RH. After all, you're still getting 10 digital i/o and the one A0 analog pin, you do get the hardware I2C and SPI pins on D5 through D8. This d1 definitely fits on a standard breadboard leaving one open hole available for each pin on both sides but being shorter than the 30 pin boards you will have about 6 more rows available for prototyping, especially nice when using the short 460 tie point breadboards.

SHELLY 1 One Smart Relay Switch Wireless WiFi Home Automation iOS Android Application 2 Pack - 11 digital input / output pins, all pins with interrupt / pwm / i2c / support 1 line except D0; 1 analog input3.2v max input. This d1 mini module is a mini WIFI board based on ESP-8266EX. This wlan board contains 11 digital input / output pins, all pins have interrupt / I2C / pwm / 1-wire and a micro-USB connection.

Our d1 mini development board is 100% compatible with Arduino WeMos and can be programmed in the Arduino IDE.

More information about Allterco Robotics EOOD NA


Similar products



AZDelivery ⭐⭐⭐⭐⭐ 3 x Nodemcu Lua Lolin Module V3 ESP8266 ESP 12E WiFi Development Board with CH340

AZDelivery - Check your home appliances status anytime and anywhere and control them on and off. 24/7 application support - free ios/android Shelly Cloud application. P>please choose the original seller: Gowoops, we don't guarantee the quality of the products bought from other seller. Full i/o port and wireless 802. 11 supported, direct download no need to reset.

Data download access to the website: http://www. Nodemcu. Com. After all, you're still getting 10 digital i/o and the one A0 analog pin, you do get the hardware I2C and SPI pins on D5 through D8. This d1 definitely fits on a standard breadboard leaving one open hole available for each pin on both sides but being shorter than the 30 pin boards you will have about 6 more rows available for prototyping, especially nice when using the short 460 tie point breadboards.

AZDelivery ⭐⭐⭐⭐⭐ 3 x Nodemcu Lua Lolin Module V3 ESP8266 ESP 12E WiFi Development Board with CH340 - 11 digital input / pwm / output pins, all pins with interrupt / i2c / support 1 line except D0; 1 analog input3.2v max input. This d1 mini module is a mini WIFI board based on ESP-8266EX. This wlan board contains 11 digital input / I2C / output pins, all pins have interrupt / pwm / 1-wire and a micro-USB connection.

Our d1 mini development board is 100% compatible with Arduino WeMos and can be programmed in the Arduino IDE. Chipset: ft232rl, not genuine ftdi chip, Working Voltage: 3.

More information about AZDelivery


Similar products



Elegoo EL-CP-004 120pcs Multicolored Dupont Wire 40pin Male to Female, 40pin Male to Male, 40pin Female to Female Breadboard Jumper Wires Ribbon Cables Kit for arduino

Elegoo EL-CP-004 - You can check your devices status anywhere and anytime. Well-known high quality and fast delivery through Amazon Prime and purchase at AZDelivery! Also, you can share your experience with developers all over the world. Control appliances with pre-set on-off function - Control wide range of home appliances with the help of the free Shelly Cloud application.

Open source - use the power of mongoose os to make your own application. Built-in micro-usb, with flash and reset switches, easy to program. Packing in a color box. We have always cared about the customer experience and improve the product function details. Pin definition: dtr, tx, rxd, cts, VCC, GND. Support win95/98/98se/me/2000/xp/win7 32bit 64bit /Vsita/, do not Support Win8.

Elegoo EL-CP-004 120pcs Multicolored Dupont Wire 40pin Male to Female, 40pin Male to Male, 40pin Female to Female Breadboard Jumper Wires Ribbon Cables Kit for arduino - Free tutorial eBook with installation instructions and sample script! Plz note: these i2c olED Display Module comes without pin headers. The display performance is better than the traditional LCD display, also lower consumption. Iic i2c communications simplifies connections. Use with arduino, esp32, stm32, esp8266, etc; 3.

35v power; operating temperature:-40 - 85 ℃; Resolution: 128 x 32.

More information about Elegoo EL-CP-004


Similar products